Z01t Odin

A 6-port 1 Gbps/100Mbps test module for testing Automotive Ethernet ECUs

Download Datasheet
software

The Z01t Odin is a 6-port 1 Gbps/100Mbps Ethernet test module designed for Automotive Ethernet test applications.

The module has native 1000BASE-T1 and 100BASE-T1 interfaces. Based on Xena’s advanced architecture, the Z01t Odin is the obvious choice for testing Automotive Ethernet up to 1G at Layers 2-3.

The module is available for the 4U 12-slot B720/2400 chassis and the easy-to-transport 1U XenaCompact chassis. It comes complete with a full range of test software (as part of the Xena Value Pack), including predefined test suites for RFC 2544, and comprehensive test automation options.

Like a guided tour of our software?

Take a free guided tour of our software. You'll see all the features, plus we'll answer any questions along the way.


Book an online meeting Try our demo

Specifications

PORT LEVEL FEATURES

  1. Interface category

    100/1000M Ethernet

  2. Total number of test ports

    6 x 100/1000M

  3. Interface options

    1000BASE-T1 or 100BASE-T1

  4. Number of physical interface form factor

    3 x RJ45 (100/1000M)

  5. Port statistics (counter size: 64 bits)

    • Link state, FCS errors, pause frames, ARP/PING, error injections, training packet
    • All traffic: RX and TX Mbit/s, packets/s, packets, bytes
    • Traffic w/o test payload: RX and TX Mbit/s, packets/s, packets, bytes

  6. Adjustable Inter Frame Gap (IFG)

    Configurable from 16 to 56 bytes, default is 20B (12B IFG + 8B preamble)

  7. Transmit line rate adjustment

    Ability to adjust the effective line rate by forcing idle gaps equivalent to -1000 ppm (increments of 10 ppm)

  8. ARP/PING

    Supported (configurable IP and MAC address per port)

  9. Field upgradeable

    System is fully field upgradeable to latest product releases (FPGA images and software)

  10. Histogram statistics (counter size: 64 bits)

    Two real-time histograms per port. Each histogram can measure one of RX/TX packet length, IFG, jitter,
    or latency distribution for all traffic, a specific stream, or a filter

  11. Tx disable

    Enable/disable of copper link

  12. IGMPv2 multicast join/leave

    IGMPv2 continuous multicast join, with configurable repeat interval

  13. Oscillator characteristics

    Z01s Odin-T1-RJ45:

    • Initial Accuracy is 3 ppm
    • Frequency drift over 1st year: ± 3 ppm (over 15 years: ± 15 ppm)
    • Temperature Stability: ± 20 ppm (Total Stability is ± 35 ppm)

TRANSMIT ENGINES

  1. Number of transmit streams per port

    256 (wire-speed). Each stream can generate millions of traffic flows through the use of field modifiers

  2. Test payload insertion per stream

    Wire-speed packet generation with timestamps, sequence numbers, and data integrity signature optionally inserted into each packet.

  3. Stream statistics (counter size: 64 bits)

    TX Mbit/s, packets/s, packets, bytes, FCS error, Pause

  4. Bandwidth profiles

    Burst size and density can be specified. Uniform and bursty bandwidth profile streams can be interleaved

  5. Field modifiers

    16-bit header field modifiers with inc, dec, or random mode. Each modifier has configurable bit-mask, repetition, min, max, and step parameters. 6 modifiers per stream

  6. Packet length controls

    Fixed, random, butterfly, and incrementing packet length distributions from 56 to 16384 bytes

  7. Packet payloads

    Repeated user specified 1 to 18B pattern, an 8-bit incrementing pattern

  8. Error generation

    Undersize length (56B min) and oversize length (16384 max.) packet lengths, injection of sequence, misorder, payload integrity, and FCS errors

  9. TX packet header support and RX autodecodes

    Ethernet, Ethernet II, VLAN, ARP, IPv4, IPv6, UDP, TCP, LLC, SNAP, GTP, ICMP, RTP, RTCP, STP, MPLS, PBB, or fully specified by user

  10. Pause Frames

    Responds to incoming pause and PFC (Priority-based Flow Control) frames

  11. Packet scheduling modes

    • Normal (stream interleaved mode) – standard scheduling mode, precise rates, minor variation in packet inter-frame gap.
    • Strict Uniform – new scheduling mode, with 100% uniform packet inter-frame gap, minor deviation from configured rates.
    • Sequential packet scheduling (sequential stream scheduling). Streams are scheduled continuously in sequential order, with configurable number of packets per stream.
    • Burst. Packets in a stream are organized in bursts. Bursts from active streams form a burst group. The user specifies time from start of one burst group till start of next burst group.

RECEIVE ENGINE

  1. Number of traceable Rx streams per port

    2016 (wire-speed)

  2. Automatic detection of test payload for received packets

    Real-time reporting of statistics and latency, loss, payload integrity, sequence error, and mis-order error checking

  3. Jitter measurement

    Jitter (Packet Delay Variation) measurements compliant to MEF10 standard with 8 ns accuracy. Jitter can be measured on up to 32 streams.

  4. Stream statistics (counter size: 64 bits)

    • RX Mbit/s, packets/s, packets, bytes.
    • Loss, payload integrity errors, sequence errors, misorder errors
    • Min latency, max latency, average latency
    • Min jitter, max jitter, average jitter

  5. Latency measurements accuracy

    ±32 ns

  6. Latency measurement resolution

    8 ns (Latency measurements can calibrate and remove latency from transceiver modules)

  7. Number of filters:

    • 6 x 64-bit user-definable match-term patterns with mask, and offset
    • 6 x frame length comparator terms (longer, shorter)
    • 6 x user-defined filters expressed from AND/OR’ing of the match and length terms.

  8. Filter statistics (counter size: 64 bits)

    Per filter: RX Mbit/s, packets/s, packets, bytes.

CAPTURE 100/1000M Ethernet

  1. Capture criteria

    All traffic, stream, FCS errors, filter match, or traffic without test payloads

  2. Capture start/stop triggers

    Capture start and stop trigger: none, FCS error, filter match

  3. Capture limit per packet

    16 – 16384 bytes

  4. Wire-speed capture buffer per port

    16 kB

  5. Low speed capture buffer per port (10Mbit/sec)

    4096 packets (any size)

PRODUCT NUMBERS FOR ORDERING

  1. Odin-1G-3S-6P-T1-RJ45

    1GE 2-speed test module with 3 x RJ-45 connectors, for 6 x 100/1000M Base-T1 copper

  2. C-Odin-1G-3S-6P-T1-RJ45

    XenaCompact 1U chassis with 1GE 2-speed test module with 3 x RJ-45 connectors, for 6 x 100/1000M Base-T1 copper

Includes this free software

software

XenaManager

Windows-based application for managing every aspect of Xena’s Ethernet traffic generation test solutions.
software

Xena2544

Xena2544 is a Windows desktop application that makes it easy to create, edit and execute test configurations in accordance with RFC 2544.
software

Xena1564

Xena1564 is a Windows desktop application that lets you analyze synchronous Ethernet and perform the Y.1564 methodology using one or more Xena test chassis.
software

Xena2889

Xena2889 makes it easy to accurately benchmark the performance of Layer 2 LAN switches according to RFC 2889.
software

Xena3918

Xena3918 is a Windows desktop application for advanced IP multicast network testing using one or more Xena test chassis, in accordance with RFC3918.

Technical Documentation

Relevant Products

...performing the same type of tests

product

Xena B720/2400

A modular high-port density chassis with space for up to 12 Xena traffic generators in a 4U form factor.

Award Winning Solutions

Xena has won multiple global awards for price/performance and technical innovation. Learn more.

footer awards

Technical Expertise

Support

Resources

Corporate

STAY IN TOUCH

Copyright © 2009-2024 Teledyne LeCroy Xena ApS, Denmark

Website Terms & Conditions / Privacy Statement / Business Terms & Conditions

Did you know you can try Xena right now?

It's easy. Just download the software and connect in seconds to a live test network so you can see how different features work. 

Try Xena Live