-
Interface category
100 /1000 /2500 / 5000 / 10000M Ethernet
-
Number of test ports
6 x 100 / 1000 / 2500 / 5000 / 10000M
-
Interface options
10GBASE-T (IEEE 802.3an)/ 5GBASE-T (IEEE 802.3bz)/ 2.5GBASE-T (IEEE 802.3bz)/ 1000BASE-T (IEEE 802.3ab) / 100BASE-T (IEEE 802.3u)
-
Interface characteristics
10GBASE-T operating at 300ft (100m) over CAT6a and CAT7 UTP cable. 5GBASE-T operating on standard Category 6 UTP cable. 2.5GBASE-T, 1000BASE-T and 100BASE-T operating on standard Category 5e UTP cable.
-
Port statistics(1)
Link state, FCS errors, pause frames, ARP/PING, error injections, training packet All traffic: RX and TX Mbit/s, packets/s, packets, bytes
Traffic w/o test payload: RX and TX Mbit/s, packets/s, packets, bytes
-
Adjustable Inter Frame Gap (IFG)
Configurable from 16 to 56 bytes, default is 20B (12B IFG + 8B preamble)
-
Transmit line rate adjustment
Ability to adjust the effective line rate by forcing idle gaps equivalent to -1000 ppm (increments of 10 ppm)
-
Transmit line clock adjustment
From -50 to 50 ppm in steps of 0.001 ppm (shared across all ports)
-
ARP/PING
Supported (configurable IP and MAC address per port)
-
Field upgradeable
System is fully field upgradeable to product releases (FPGA images and Software)
-
Histogram statistics(1)
Two real-time histograms per port. Each histogram can measure one of RX/TX packet length, IFG, or latency distribution for all traffic, a specific stream, or a filter
-
Tx disable
Enable/disable of copper link
-
IGMPv2 multicast join/leave
IGMPv2 continuous multicast join, with configurable repeat interval
-
Oscillator characteristics
Z10r Odin:
- Initial Accuracy is 3 ppm
- Frequency drift over 1st year: ± 3 ppm (over 15 years: ± 15 ppm)
- Temperature Stability: ± 20 ppm (Total Stability is ± 35 ppm)
-
Number of transmit streams per port
256 (wire-speed) Each stream can generate millions of traffic flows through the use of field modifiers
-
Test payload insertion per stream
Wire-speed packet generation with timestamps, sequence numbers, and data integrity signature optionally inserted into each packet.
-
Stream statistics(1)
TX Mbit/s, packets/s, packets, bytes, FCS error
-
Bandwidth profiles
Burst size and density can be specified. Uniform and bursty bandwidth profile streams can be interleaved
-
Field modifiers
16-bit header field modifiers with inc, dec, or random mode. Each modifier has configurable bit-mask, repetition, min, max, and step parameters. 4 modifiers per stream.
-
Packet length controls
Fixed, random, butterfly, and incrementing packet length distributions. Packet length from 56 to 12288 bytes
-
Packet payloads
Repeated user specified 1 to 18B pattern, an 8-bit incrementing pattern
-
Error generation
Undersize length (56B min) and oversize length (12288 max.) packet lengths, injection of sequence, misorder, payload integrity, and FCS errors
-
TX packet header support and RX autodecodes
Ethernet, Ethernet II, VLAN, ARP, IPv4, IPv6, UDP, TCP, LLC, SNAP, GTP, ICMP, RTP, RTCP, STP, MPLS, PBB, or fully specified by user
-
Pause Frames
Responds to incoming pause frames
-
Pause Frames
Responds to incoming pause frames
-
Packet scheduling modes
• Normal (stream interleaved mode). Standard scheduling mode, precise rates, minor variation in packet inter-frame gap
• Strict Uniform. New scheduling mode, with 100% uniform packet inter-frame gap, minor deviation from configured rates.
• Sequential packet scheduling (sequential stream scheduling). Streams are scheduled continuously in sequential order, with configurable number of packets per stream.
• Burst. Packets per stream are organized in bursts. Bursts from active streams form a burst group. The user specifies time from start of one burst group till start of next burst group.
-
Number of traceable Rx streams per port
2016 (wire-speed)
-
Automatic detection of test payload for received packets
Real-time reporting of statistics and latency, loss, payload integrity, sequence error, and misorder error checking
-
Jitter measurement
Jitter (Packet Delay Variation) can be measured on up to 32 streams.bJitter measurements compliant to MEF10 standard with 8 ns accuracy
-
Stream statistics(1)
• RX Mbit/s, packets/s, packets, bytes.
• Loss, payload integrity errors, sequence errors, misorder errors
• Min latency, max latency, average latency
• Min jitter, max jitter, average jitter
-
Latency measurements accuracy
±8 ns
-
Latency measurement resolution
8 ns (Latency measurements can calibrate and remove latency from transceiver modules)
-
Number of filters:
6 x 64-bit user-definable match-term patterns with mask, and offset
6 x frame length comparator terms (longer, shorter)
6 x user-defined filters expressed from AND/OR’ing of the match and length terms
-
Filter statistics(1)
Per filter: RX Mbit/s, packets/s, packets, bytes.
DataSheet
5-speed 6-port 10G test module
